INTERGRAIN Enviropro Endure 1 Pack 5L (Gloss, Satin or Matt)

$137.50 tax incl.

Add to cart

A highly durable, non-yellowing, water based coating for use on timber and parquetry floors. Endure 1 pack is low in odour and fast drying allowing the job to be completed in one day. Endure 1 pack is available in gloss, satin and matt.

More details

Add to my wishlist

Description
Intergrain Enviropro Endure 1 Pack is a high performance, environmentally responsible, water based polyurethane for timber and parquetry floors. Endure 1 Pack systems are highly durable and are the product of choice for floors that require a high quality. Endure 1 Pack has the added features of being low odour, quick drying and non-yellowing.

Where to use
Timber and parquetry floors.
Note: Endure 1 Pack may be used on cork and floating floors in certain situations. For more information, please call 1800 248 780.

Gloss Level
Gloss, Satin and Matt

Preparation
All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination. If uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with IntergrainWoodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with a commercial grade vacuum cleaner.

Mixing
Shake the Endure 1 Pack for 1 minute or until any settled matting agent is reincorporated. Strain product.

Application
New Timber: Where a sealer is required, apply 1 coat of Enviropro Timbersealor TimberSeal Ultra following the instructions on the label. Lightly sand the sealer with a worn 150 mesh screen if needed. Apply 2 coats of Endure 1 Pack at 8-10m²/L using a 11mm Selleys Spirit micro-fibre roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen.
Recoating Timber: To ensure adhesion, a test patch is recommended after the surface has been prepared. Wash the floor with Enviropro Squeaky Cleanas per the label instructions. Sand with 100 grit screen then vacuum thoroughly and tack clean with a damp rag. Apply 1 coat of Endure 1 Pack at 8 - 10m²/L using a 11mm Selleys Spirit micro-fibre roller.
For new and existing timber, any contaminants that appear between coats will cause inconsistencies in the final film. It is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 1 Pack. On porous timbers, up to 3 coats of Endure 1 pack can also be applied to maximise the uniformity of the finish.

No. of Coats
3 Coats. (1 coat Timberseal, 2 coats Endure 1 pack)

Coverage Rate
8-10m²/L*

Touch Dry
1 hour^

Recoat Time
3 hours^

Clean up with
Water

Packaging Sizes
5L

*Coverage rates are subject to variation between different timber species. To ensure adequate timber protection, this coverage should not be exceeded.
^ These dry times are based on drying conditions of 25°C and 50% relative humidity. Dry times will be subject to climatic conditions, film thickness and airflow. Use below 10°C is not advised. If using above 30°C, use of EnviroproWet Edge Extender is recommended. It is not advised to apply coatings when the temperature exceeds 35°C as they may dry too quickly under the roller, resulting in a substandard finish. The drying time will vary greatly when the temperature is below 10°C or above 30°C, or if the relative humidity is higher than 50%.

Please refer to the instructions provided on the Intergrain Enviropro Endure 1 Pack container before commencing your project.

  • Size 5L

No customer comments for the moment.

Only registered users can post a new comment.

Cart  

No products

Shipping $0.00
Total $0.00

Cart Check out