INTERGRAIN Enviropro Endure 2 Pack with Hardener 4.5L+0.5L (Gloss, Satin or Matt)

$168.30 tax incl.

Add to cart

An exceptionally durable, non-yellowing water based coating for use on timber and parquetry floors. Endure 2 pack uses cross-linking technology to produce a tough commercial grade finish. Endure 2 pack is available in gloss, satin and matt.

More details

Add to my wishlist

Description 
Intergrain Enviropro Endure 2 Pack is an exceptionally durable, environmentally responsible, water based polyurethane for timber and parquetry floors. Endure 2 Pack uses cross-linking technology making it the ideal product for high traffic and commercial environments. Endure 2 Pack has the added features of being low odour, quick drying and non-yellowing.

Where to use
Timber and parquetry floors.
Note: Endure 2 Pack may be used on cork and floating floors in certain situations. For more information please call 1800 248 780.

Gloss Level 
Gloss, Satin and Matt

Preparation
All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination. If uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with Intergrain Woodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with the commercial grade vacuum cleaner.

Mixing
Mix Endure 2 Pack Part A and Endure 2 Pack Part B at a ratio of 9 to 1 and shake for two minutes. Strain product. Endure 2 Pack has a pot life of 2 hours.

Application 
New Timber: Where a sealer is required, apply 1 coat of Enviropro Timberseal or TimberSeal Ultra following the instructions on the label. Lightly sand the sealer with a worn 150 mesh screen if needed. Apply 2 coats of Endure 2 Pack at 8-10m²/L using a 11mm Selleys Spirit micro-fibre roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen.

Recoating Timber: To ensure adhesion, a test patch is recommended after the surface has been prepared. Wash the floor with Envriopro Squeaky Clean as per the label instructions. Sand with 100 grit screen then vacuum thoroughly and tack clean with damp rags. Apply 1 coat of Endure 2 Pack at 8-10m²/L using a 11mm Selleys Spirit micro-fibre roller.

Note: For new and recoating timber, any contaminants that appear between coats will cause inconsistencies in the final film. For the final coat, it is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 2 Pack. On porous timbers, up to 3 coats of Endure 2 pack can also be applied to maximise the uniformity of the finish.

No. of Coats
3 coats (1 coat Timberseal, 2 coats Endure 2 pack)

Coverage Rate
8-10m²/L*

Touch Dry
1 hour^

Recoat Time
3 hours^

Clean up with 
Water

Packaging Sizes 
5L

*Coverage rates are subject to variation between different timber species. To ensure adequate timber protection, this coverage should not be exceeded.
^ These dry times are based on drying conditions of 25°C and 50% relative humidity. Dry times will be subject to climatic conditions, film thickness and airflow. Use below 10°C is not advised. If using above 30°C, use of Enviropro Wet Edge Extender is recommended. It is not advised to apply coatings when the temperature exceeds 35°C as they may dry too quickly under the roller, resulting in a substandard finish. The drying time will vary greatly when the temperature is below 10°C or above 30°C, or if the relative humidity is higher than 50%.

Please refer to the instructions provided on the Intergrain Enviropro Endure 2 Pack container before commencing your project.

  • Size 4.5L + 0.5L

No customer comments for the moment.

Only registered users can post a new comment.

Cart  

No products

Shipping $0.00
Total $0.00

Cart Check out